Email Troubleshooting

Below are listed the most common email problems reported to us that are usually related to the set-up on your computer or other external factors.

I cannot receive email.

Make sure you are on-line (can you browse web pages?) If you cannot browse web pages, check your internet connection or contact your ISP before reporting an email problem.
Have you installed or configured a firewall? Try receiving with the firewall temporarily turned off - if this works OK then consult the documentation for the firewall or contact the firewall vendors help desk.
Make sure you have used the correct user name, password and mail server addresses for your account. This information can be found on the Control Panel site (including specific step by step instructions for various popular mail clients).
We have seen that some email clients (especially Outlook Express) choke on some type of spam email. You can inspect your incoming mail queue using the Control Panel site and delete any messages you don't want to download (make sure you close your email client while you do this). This often resolves the problem.

Make sure you are on-line (as above).
The usual cause of this is not enabling SMTP authentication in your mail client. All outgoing mail sent via our mail server requires authentication (more information can be found at the Control Panel site ).
If you get an error message about "too many recipients" then please note that the maximum number of recipients you can have on one outgoing email is 30. This is an anti-spam measure. If you have more than 30 recipients you'll need to split them over several emails. If you email the same list regularly ask us about setting up a mailing list.
Some users have reported problems sending large messages over a wireless connection. Tests usually show that the same message can be sent on a wired connection without any problems. Check that your wireless devices have up to date drivers and good reception.
If you use an ISP such as Freeserve/Wanadoo or AOL they may intercept your outbound email and process it through their own servers. This is an anti-spam measure. If this causes you a problem you can change your email software to use port 1400 instead of port 25 for outbound mail (in Outlook this setting is on the 'Advanced' tab within the email account properties).

The recipient may not have enough free space in their mailbox.
Most ISPs impose a size limit on all messages. This can be as little as 1Mb, although 5 to 10Mb is more usual. There is nothing we can do to force a large message through in this case.
Remember if you are sending a large message that the recipient may only have a dial-up internet connection, and a message of more than 1Mb may take them a long time to download.

This occurs when you have set up your mail client to leave copies of incoming messages on the server without turning on the option to delete it after a few days. Turn off the 'leave a copy' option, or turn on the 'remove after n days' option.

This occurs when you have set up your mail client to leave copies of incoming messages on the server. It is usually caused by changing the user profile or mail settings which makes the program lose track of which messages have already been downloaded. There is nothing we can do to prevent this from happening. Consider turning off the 'leave a copy' option.

Our summaries don't contain any sender information because viruses like Netsky typically use faked sender details. Therefore it's usually impossible to tell where the email has really come from. Also, as these viruses act without the knowledge of the infected PC owner, it's not usually the case that you are being deliberately targeted.
The main purpose of us sending out these messages is just to provide some feedback on the amount of mail we receive but don't pass on to your mailbox, as blocked emails unfortunately count towards the bandwidth usage on which we base the hosting cost. Unless you are getting hundreds or thousands of blocked messages it should have little effect on you though.

Do you have your email client set up to send and receive messages automatically?
If you use our email virus scanning service, it may take up to five minutes for email to be scanned, depending on the current server load. Many virues-infected emails arrive in 'waves' which produce a temporary high server load.

We use the SpamHaus blocklist to prevent junk email being accepted from known spammers. The sender or their ISP may be on the blocklist because they have allowed junk email to be sent from their equipment (knowingly or not). They should consult the SpamHaus website for more information on how to get removed from the list. We cannot make any special exceptions for senders blocked this way.

The sender's mail server probably has an incorrect reverse DNS pointer.
The senders ISP must correct this before we will accept mail from them. This is another anti-spam measure and is recommended by RFC 1912 .
The sender most probably also has problems sending mail to other ISPs.
The sender's ISP can check their DNS setup at http://www.dnsreport.com (pay particular attention to the results in the 'MX' section).

Viruses and spammers can fake the 'from' address on emails they send out, sometimes using non-existant addresses but sometimes using the real addresses of innocent third parties. You may be unlucky enough to have your own email address used in this way. Although we use the SPF (Sender Policy Framework) to try and prevent this problem, not all ISPs recognise SPF and so you receive any bounces or replies generated by the virus/spam.
There is nothing we can do to block these messages.
You may find the problem is worse if you have a catch-all email address - consider dropping the catch-all address.